AMS4122 is a dual switching regulator capable to deliver up to 2A for each channel. Internally Compensated internal Soft Start makes AMS4122 one of the simplest and easiest switching regulators to use with the minimum external components. Each regulator has independent hiccup current limit. The Enable pin turns both devices on when a voltage of 2.5V or higher it is applied to EN pin. Since both devices share one single package the thermal protection turns off both devices when the die temperature exceeds approximately 135°C. Both regulators are adjustable using a 0.600V reference for low output voltage settings. The oscillators are 180° phase to each other to reduce the ripples on the input power supply and minimize the power dissipation on the package. The device can be easily configured for Two Phase single output switching regulator capable of 5A output load. By applying a 2.5V or greater on feedback pin of the second switching regulator the device enters in Two Phase Mode.

The first benefit of having a Two Phase device is reducing the output ripples by a factor of four as the single phase. The second benefit is higher output current capability at overall low cost. AMS4122 combined with AMS4123 (2A Switching Regulator + 1A LDO in SO-8) makes complete solution for LCD TV power requirements. Available in 8-pin SOIC EDP package. Download data sheets

AMS4123 is a switching regulator capable to deliver up to 2A and one LDO rated for 1A output in a single SO-8 EDP package. The switching regulator is Internally Compensated internal Soft Start to reduce to minimum external components. The regulator has hiccup current limit and thermal protection. The Enable pin has built-in power-up sequencing externally programmable. If 2.0V or higher it is applied to EN pin it turns on the Switching Regulator. By increasing the voltage to 2.5V or more it turns on the LDO section. Since both circuits share one single package the thermal protection turns off both circuits when the die temperature exceeds approximately 135?C. Both regulators are adjustable using a 0.600V reference for low output voltage settings. The LDO has options for fixed output voltages from 0.6V to 5V in 100mV steps. The LDO input can be supplied from the Switching Regulator output increasing the efficiency but can supplied as well from another source that is equal or lower than the device supply voltage. With a Dropout of 400mV @1A makes AMS4123 the perfect solution for low noise 1.8V from a 2.5V source. The AMS4123 combined with AMS4122 (2A Dual Switching Regulator in SO-8) makes complete solution for LCD TV power requirements. Download data sheets

AMS4151 is a step-down converter for high voltage applications. Current mode operation provides easier compensation and fast transient response. Internal soft start reduces the number of external components. Thermal shutdown and cycle-by-cycle current limiting protects the device in extreme conditions. AMS4151 is available in 8-pin SOIC EDP package. Download data sheets

AMS4152 is a step-down converter for high voltage applications. Current mode operation provides easier compensation and fast transient response. Internal cycle-by-cycle current limiting and thermal shutdown. A 5V reference voltage available that can supply up to 2mA load. AMS4152 is available in 8-pin SOIC EDP package. Download data sheets

AMS4153 is a step-down converter for high voltage applications. Current mode operation provides easier compensation and fast transient response. Internal cycle-by-cycle current limiting and thermal shutdown.. AMS4153 is available in 8-Pin SO-8 EDP package. Download data sheets

AMS4154 is a 2A step-down converter for high voltage applications. Current mode operation provides easier compensation and fast transient response. Internal cycle-by-cycle current limiting and thermal shutdown provides the necessary protection in faults situation. A 5V reference voltage is available that can supply up to 2mA current. Available in 8-pin SOIC EDP package. Download data sheets

AMS4155 is a monolithic step down switch mode converter with a built in internal power Switch Transistor. It achieves 2A continuous output current over a wide input supply range with excellent load and line regulation. Current mode operation provides fast transient response and eases loop stabilization. Fault condition protection includes cycle-by-cycle current limiting and thermal shutdown. In shutdown mode the regulator draws 17?A of supply current. Available in 8-pin SOIC EDP package. Download data sheets

AMS4106 is a medium output current synchronous buck converter. The high side device is integrated into the device. The AMS4106 provides an adaptive gate drive for the external FET. For low current operation this can be replaced with a Schottky diode allowing asynchronous operation. The part has either a fixed internal present PWM frequency of 250 kHz, or externally adjustable up to 600 kHz, allowing smaller inductors where efficiency is less critical and faster transient response is needed. The part uses current mode control for simple compensation and ease of use with low ESR capacitors. It uses a programmable soft start to reduce inrush current and allow large output capacitors to be used where very low ripple is required. The part has enable pin with virtual zero power in shutdown mode. A power good is provided with open collector to facilitate power ready functions. The part is available in SOIC 16 thermally enhanced packages. Download data sheets

AMS2596 series of regulators are monolithic integrated circuits that provide all the active functions for a step-down (buck) switching regulator with internal compensation and soft start capable of driving a 3A load with excellent line and load regulation. These devices are available in adjustable voltage and fixed output voltages of 1.25V to 7V in 100mV increments. The AMS2596 require a minimum number of external components and simple to use. AMS2596 operates at a switching frequency of 175 kHz thus allowing smaller sized filter components than what would be needed with lower frequency switching regulators. AMS2596 series are available in 8-Lead SOIC, 5-Lead TO-252, and a 5-Lead TO-220/TO-263 packages. Download data sheets

AMS4160 The AMS4160 is a PWM controller designed for use in step down DC/DC power supply. A simple, fixed frequency, highly efficient buck regulator can be implemented using the AMS4160 with minimal external components. The input voltage range is from +3.3V to +20V. The small footprints of SO-8 package allows for compact circuit design. A 0.6V reference allows output voltage settings to less than 1V. AMS4160 operates at a fixed frequency of 200 kHz optimized for high efficiency and low cost. AMS4160 has a thermal protection circuit and current limit. Download data sheets

AMS6101 is an adjustable step-up DC/DC converter with a 2A internal switch. With the ability to set the output voltage up to 23V, the AMS6101 is an ideal part for biasing TFT displays. The AMS6101 can be operated at switching frequencies of 600 kHz allowing for easy filtering and low noise. An external compensation pin gives the user flexibility in setting frequency compensation, which makes possible the use of small, low ESR ceramic capacitors at the output. The AMS6101 is available in a low profile 8-lead SOIC EDP (thermally enhanced) package. Download data sheets

AMS6104 is an adjustable step-up DC/DC converter with a 1Amp internal switch. The low quiescent current of typical 300?A, makes AMS6104 attractive for battery operated applications. AMS6104 operates at switching frequencies of 500 kHz allowing for easy filtering and low noise. The reference voltage is set at 1.25V and the maximum duty cycle is 80% to minimize the stress on the switching transistor. Internally compensated and internal soft-start minimizes the number of external components necessary. It operates from 1.6V to 15V supply and it is thermally and over current protected. The AMS6104 is available in SOT23-5 leads package. Download data sheets

Tape and Reel packing is available for all SO, SOT-223, TO-92, DD and D packages. Surface mount packages are retained in an embossed carrier tape by a cover tape. For TO-92 package, the leads are secured to a backing tape by a cover tape.
Download Data sheets